Do You like your car?

tain necessary sometimes the vehicle. What can you do to buy certainly a good car? Very often it is recommended to select a proposed us a car to the garage. The perfect solution would be that if we had a friendly workshop where ou

Dodane: 04-09-2016 11:42
Do You like your car? reduce smoke Abarth

Used cars - as well choose?

Used cars are much less expensive than acquiring your dream vehicle straight from the showroom. Not surprisingly, it is a very popular way to quickly obtain necessary sometimes the vehicle. What can you do to buy certainly a good car? Very often it is recommended to select a proposed us a car to the garage. The perfect solution would be that if we had a friendly workshop where our friend after a review by a special software this car could tell us a lot about him. Experienced car mechanics unhindered see if the car has already passed through some accident or has other hidden defects, which would like to avoid a potential car owner.


high power-to-weight

Reciprocating piston engines are by far the most common power source for land and water vehicles, including automobiles, motorcycles, ships and to a lesser extent, locomotives (some are electrical but most use Diesel engines45). Rotary engines of the Wankel design are used in some automobiles, aircraft and motorcycles.

Where very high power-to-weight ratios are required, internal combustion engines appear in the form of combustion turbines or Wankel engines. Powered aircraft typically uses an ICE which may be a reciprocating engine. Airplanes can instead use jet engines and helicopters can instead employ turboshafts; both of which are types of turbines. In addition to providing propulsion, airliners may employ a separate ICE as an auxiliary power unit. Wankel engines are fitted to many unmanned aerial vehicles.
Big Diesel generator used for backup power
Combined cycle power plant

ICEs drive some of the large electric generators that power electrical grids. They are found in the form of combustion turbines in combined cycle power plants with a typical electrical output in the range of 100 MW to 1 GW. The high temperature exhaust is used to boil and superheat water to run a steam turbine. Thus, the efficiency is higher because more energy is extracted from the fuel than what could be extracted by the combustion turbine alone. In combined cycle power plants efficiencies in the range of 50% to 60% are typical. In a smaller scale Diesel generators are used for backup power and for providing electrical power to areas not connected to an electric grid.

Small engines (usually 2?stroke gasoline engines) are a common power source for lawnmowers, string trimmers, chain saws, leafblowers, pressure washers, snowmobiles, jet skis, outboard motors, mopeds, and motorcycles.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


The first part of the piston downstroke

Other cycles

The very first internal combustion engines did not compress the mixture. The first part of the piston downstroke drew in a fuel-air mixture, then the inlet valve closed and, in the remainder of the down-stroke, the fuel-air mixture fired. The exhaust valve opened for the piston upstroke. These attempts at imitating the principle of a steam engine were very inefficient. There are a number of variations of these cycles, most notably the Atkinson and Miller cycles. The diesel cycle is somewhat different.

Split-cycle engines separate the four strokes of intake, compression, combustion and exhaust into two separate but paired cylinders. The first cylinder is used for intake and compression. The compressed air is then transferred through a crossover passage from the compression cylinder into the second cylinder, where combustion and exhaust occur. A split-cycle engine is really an air compressor on one side with a combustion chamber on the other.

Previous split-cycle engines have had two major problems?poor breathing (volumetric efficiency) and low thermal efficiency. However, new designs are being introduced that seek to address these problems.

The Scuderi Engine addresses the breathing problem by reducing the clearance between the piston and the cylinder head through various turbo charging techniques. The Scuderi design requires the use of outwardly opening valves that enable the piston to move very close to the cylinder head without the interference of the valves. Scuderi addresses the low thermal efficiency via firing after top dead centre (ATDC).

Firing ATDC can be accomplished by using high-pressure air in the transfer passage to create sonic flow and high turbulence in the power cylinder.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine